Vertical Machining Centers LV-1170 / LV-1370
X-axis 1300 mm
Y-axis 700 mm
Z-axis 700 mm

Vertical Machining Centers Unmatched Performance By Master

The LV series is a flagship with unmatched machining performance. It is specially designed to exhibit optimal structure, high rigidity and high accuracy. In addition, its wide range of machining, powerful spindle motor as well as flexible machining capabilities make it ideal for upgrading industry.

  1. The optional bed construction design is able to resist inertia generated by high‭ “‬G‭” ‬with‭ ‬maximum stability‭.‬
  2. The short nose spindle presents outstanding rigidity‭. ‬It also may increase efficiency while lowering tool wear‭.‬
  3. 32 ‬meters rapid traverse on three axes greatly reduces machining time‭.
  4. Stable automatic tool change system not only reduces non-cutting time, but also extends spindle life.
  5. Front side chip exhaust with optimal chip exhausting angles and extra large chip flushing rate.

1 Products_LVF1

Taiwan Master Tool Magazines.

  • The entire series of machine employs‭ ‬Taiwan master tool magazines.
  • The tool pockets are manufactured from aluminum alloy and T6‭ ‬treated for maximum durability‭.‬
  • Front mounted air cylinder enables repair or maintenance to be accomplished in only 10‭ ‬minutes‭.‬

Short Spindle Nose

The short spindle nose design allows the spindle motor to fully develop transmission efficiency‭. ‬As a result‭, ‬machining accuracy‭ ‬is upgraded and spindle life is extended‭.‬

Ball Screw、Linear Motion Guide

The silent ball screws and linear guide ways on three axes feature high rigidity‭, ‬low noise‭, ‬low friction and high sensitivity‭, ‬providing an increase in machining speed and accuracy‭.‬

Pneumatic counter-balance on Z-axis

The Z-axis is designed with no counter-balance weight in combination with servo motor drive with brake to improve Z-axis drive performance‭. ‬Therefore‭, ‬high speed and better surface finish can be achieved‭.‬

Full-enclosed Guards

Fully enclosed guards ensure smooth movement at high speed and low noise‭. ‬The guards isolate coolant and chips and provide a protection for linear ways and ball screws for extending their service life‭.‬

Table‭ size :

2 Products_LVF2

Coolant Jets Around Spindle


The coolant jets around spindle device employs 4 coolant nozzles around the spindle, that provides the best cooling effect to the tool and the workpiece resulting in better machining quality.

Direct-drive Spindle(optional)


With the direct-drive design‭, ‬the motor is directly coupled to the spindle‭. ‬This feature may eliminate noise and backlash problems usually occured on a belt-drive or gear-drive system‭, ‬while providing a full-power rotation‭.‬

The spindle head is a symmetrical design to reduce thermal deformation due to temperature difference‭.‬

Floating type spindle tool knocking design prevents tool knocking force from directly exerting on the bearings‭, ‬that results in‭ ‬extended bearing life‭.

Collision Protection Device


The machine is equipped with a collision protection device which can absorb and reduce the collision force. The machine accuracy is still maintained if any axis malfunction happens.

Large Capacity Coolant Tank


Cutting tank capacity of 200L, cutting calories can be quickly discharged.

Tank design uses door type, and placement of the rear side of the machine, saving space.


Model MV-1685 LV-1370
X‭-‬axis travel 1100 mm 1300 mm
Y‭-‬axis travel 700 mm 700 mm
Z‭-‬axis travel 700 mm 700 mm
Spindle nose to table 120~820 mm 120~820 mm
Type of spindle BT-40 BT-40
Spindle transmission Belf Drive Belf Drive
Spindle R.P.M. 8,000 rpm 8,000 rpm
Spindle motor 11 kw 15 kw
X/Y/Z rapid traverse 32 / 32 / 30 M/min 32 / 32 / 30 M/min
Three axes ball screws‭ ‬(mm) ø40 / P12 / C3 ø40 / P12 / C3
Three axes linear guide (P class) X, Z-axis ball screw: ball type 45 mm x 6 blocks

Y-axis ball screw: ball type 45 mm x 4 blocks

Three axes transmission method Direct drive Direct drive
Cutting feed rate 1~10,000 mm/min 1~10,000 mm/min
Table size 1200 x 700 mm 1400 x 700 mm
T-slot‭ ‬(‬WxNo‭.‬xPitch) 18 x 5 x 130 mm 18 x 5 x 130 mm
Table loading capacity 700 kg 850 kg
Tool selection method Rotary disc type Rotary disc type
No‭. ‬of tools 24 pcs 24 pcs
Max‭. ‬tool weight 7 kgs 7 kgs
Coolant tank capacity 250 L 250 L
Max‭. ‬machine weight 7100 kg 7500 kg
Machine‭ ‬size‭ ‬(LxWxH)‭‬ 3300 x 3005 x 3200 mm 3300 x 3005 x 3200 mm
Air pressure 6 kg 6 kg
Power requirement 25 KVA 25 KVA

•‭ ‬Design and specification are subject to change without prior notice‭.

Standare Accessories:

  • BT40 spindle
  • 8,000 rpm Belt drive
  • Rotary disc type (BT40,24 tools)
  • Built-in coolant nozzles
  • Spindle oil cooler
  • Automatic lubrication system
  • M30 automatic power off
  • Ethernet transfer
  • LED work ligh
  • Rigid tapping

Option Accessories:

  • 10,000/12,000 rpm direct-drive spindle
  • Pneumatic counter-balance on Z-axis
  • Rotary disc type (BT50,24 tools)
  • Programmable coolant nozzle adjustment
  • Coolant through spindle (15 bar/20 bar)
  • 4th axis rotary table and tailstock
  • Automatic tool measuring device
  • Increase height of column
  • Screw type chip conveyor
  • Link chain type chip conveyor
  • Oil / fluid separation device
  • Coolant gun and air gun


Dynamic roundness inspection

Dynamic roundness inspection

Laser inspection

Laser inspection