Vertical Machining Centers MV-1685
Box Way/Gear Head
X-axis 1600 mm
Y-axis 850 mm
Z-axis 3800 mm

Vertical Machining Centers Unmatched Performance By Master

The MV series is a flagship with unmatched machining performance. It is specially designed to exhibit optimal structure, high rigidity and high accuracy. In addition, its wide range of machining, powerful spindle motor as well as flexible machining capabilities make it ideal for upgrading industry.

  1. The optional bed construction design is able to resist inertia generated by high “G” with maximum stability.‬
  2. The short nose spindle presents outstanding rigidity. It also may increase efficiency while lowering tool wear.
  3. Pneumatic counter-balance on Z-axis.
  4. Front side chip exhaust with optimal chip exhausting angles and extra large chip flushing rate.


Taiwan Master Tool Magazines.

  • The entire series of machine employs‭ ‬Taiwan master tool magazines.
  • The tool pockets are manufactured from aluminum alloy and T6‭ ‬treated for maximum durability‭.‬
  • Front mounted air cylinder enables repair or maintenance to be accomplished in only 10‭ ‬minutes‭.‬

Short Spindle Nose

The short spindle nose design allows the spindle motor to fully develop transmission efficiency‭. ‬As a result‭, ‬machining accuracy‭ ‬is upgraded and spindle life is extended‭.‬

Ball Screw、Linear Motion Guide

The silent ball screws and linear guide ways on three axes feature high rigidity‭, ‬low noise‭, ‬low friction and high sensitivity‭, ‬providing an increase in machining speed and accuracy‭.‬

Pneumatic counter-balance on Z-axis

The Z-axis is designed with no counter-balance weight in combination with servo motor drive with brake to improve Z-axis drive performance‭. ‬Therefore‭, ‬high speed and better surface finish can be achieved‭.‬

Full-enclosed Guards

Fully enclosed guards ensure smooth movement at high speed and low noise‭. ‬The guards isolate coolant and chips and provide a protection for linear ways and ball screws for extending their service life‭.‬

Table‭ size :


Coolant Jets Around Spindle


The coolant jets around spindle device employs 4 coolant nozzles around the spindle, that provides the best cooling effect to the tool and the workpiece resulting in better machining quality.

Direct-drive Spindle(optional)


With the direct-drive design‭, ‬the motor is directly coupled to the spindle‭. ‬This feature may eliminate noise and backlash problems usually occured on a belt-drive or gear-drive system‭, ‬while providing a full-power rotation‭.‬

The spindle head is a symmetrical design to reduce thermal deformation due to temperature difference‭.‬

Floating type spindle tool knocking design prevents tool knocking force from directly exerting on the bearings‭, ‬that results in‭ ‬extended bearing life‭.

Collision Protection Device


The machine is equipped with a collision protection device which can absorb and reduce the collision force. The machine accuracy is still maintained if any axis malfunction happens.

Large Capacity Coolant Tank


Cutting tank capacity of 200L, cutting calories can be quickly discharged.

Tank design uses door type, and placement of the rear side of the machine, saving space.


Model MV-1685
X‭-‬axis travel 1600 mm
Y‭-‬axis travel 850 mm
Z‭-‬axis travel 800 mm
Spindle nose to table 150~950 mm
Type of spindle BT-40
Spindle transmission Gear Head
Spindle R.P.M. 6,000 rpm
Spindle motor 15 kw
X/Y/Z rapid traverse 20 / 20 / 15 M/min
Three axes transmission method Direct drive
Cutting feed rate 1~10,000 mm/min
Table size 1700 x 800 mm
T-slot‭ ‬(‬WxNo‭.‬xPitch) 22 x 5 x 160 mm
Table loading capacity 2000 kg
Tool selection method ARM type
No‭. ‬of tools 24 / 32 pcs
Max‭. ‬tool weight 18 kgs
Coolant tank capacity 300 L
Max‭. ‬machine weight 10,450 kg
Machine‭ ‬size‭ ‬(LxWxH)‭‬ 4550 x 4000 x 4000 mm
Air pressure 6 kg
Power requirement 35 KVA

•‭ ‬Design and specification are subject to change without prior notice‭.

Standare Accessories:

  • BT50 / 24 tools
  • 6,000 rpm gear head
  • Built-in coolant nozzles
  • Pneumatic counter-balance on Z-axis
  • Automatic lubrication system
  • M30 automatic power off
  • LED work ligh
  • Rigid tapping

Option Accessories:

  • 32 / 40 tools
  • Programmable coolant nozzle adjustment
  • 4th axis rotary table and tailstock
  • Automatic tool measuring device
  • Spindle oil cooler
  • Increase height of column
  • Screw type chip conveyor
  • Link chain type chip conveyor
  • Oil / fluid separation device
  • Coolant gun and air gun




Dynamic roundness inspection

Dynamic roundness inspection

Laser inspection

Laser inspection